Product - Shamawar Group of Companies

IPC is used for simultaneous penetration of insulation on LV ABC conductors and for connecting of conductors for street lighting. Connector is manufactured in such way that it enables connection of LV ABC and branch conductor regardless of whether it is an aluminum or copper conductor. The body of the connector is made of Heat and UV resistant plastic and the elastomer insert eliminates the appearance of electrolytic corrosion since it prevents the appearance of moisture at contact points. The contacts are protected with electric contact grease. Mounting under voltage is possible but with mandatory use of adequate protection equipment. Ring-spanner or tubular spanner.

MODEL : IPCH-01Insulating Piercing Connector Holder, IPCH-01 made from Aluminum Alloy high grade Tool was tested according to NFC 033-020:2013 and can with stand torque up to 40kN.

Weight : 450 g.
Minimum clamping jaw: 40 mm
Maximum clamping opening: 70 mm

MODEL : IPCH-01

Insulating Piercing Connector Holder, IPCH-01 made from Aluminum Alloy high grade Tool was tested according to NFC 033-020:2013 and can with stand torque up to 40kN.

Weight : 450 g.
Minimum clamping jaw: 40 mm
Maximum clamping opening: 70 mm

Low voltage metal oxide surge arresters with a silicone housing NNO and MOSPO are designed for installation in low voltage power lines or junction boxes with voltages up to 1 kV.They serve as the initial level of protection against surges and other transients. The varistors of low voltage surge arresters NNO and MOSIPO are directly molded by silicone rubber, providing them with a high level of ingress protection rated at IP 67.

Hubbell offers both IEEE and IEC compliant distribution arrester products. The application may dictate the use of a different design to handle excessive lightning duty, high TOV or offer superior equipment protection.Distribution arresters are commonly applied on system voltages from 3 – 46 kV. Use this guide to help select the correct arrester classification for your specific application. Other designs are available for unique applications.

IEC Class Station Medium Polymer Housed Surge Arrester

High quality solid-core station class arresters qualified to both IEEE and IEC arrester standards

PVI-LP arresters comply with the latest revision of IEC 60099-4
Long lasting ESP^TM housing material with superior mechanical strength and electrical characteristics
Robust sealing system protects internal components from moisture ingress to extend service lifetime
High quality MOV discs made in Wadsworth, Ohio since 1978

Neutral link 100A was designed for continuous operation on a 3-phase, 415V, 50 Hz multiple neutral earthed system.Housing Made from weather and UV resistant, fire retardant insulating material. A hole/slot each at the top and bottom.Manufactured in 2 parts i.e., top cover and base molding. Sealing provided to seal the top cover to the base Base moldingTerminal Block Connector Design with a hole Internal Diameter = 9mm, at least 2 pinching screws/stud of 8mm(M8) per hole, with incoming and outgoing hole. Inner side of hole is with threaded.Pinching screw and terminal shall made of tin plated brass. Pinching screw and terminal shall be electro- tin plated in accordance to BS 1872. Filled sufficient quantity of electrical conductive oxide inhibiting compound.

ANSI C119.4, full tension, Class A connector (95% of conductor breaking strength unless otherwise noted)
Color coded end funnel guides for easy identification
Factory inhibitor protected
Fastest method of splicing aluminum, aluminum alloy and ACSR conductor

Photo Electric Control Unit (PECU) is an electronic switch which is triggered at a specific light level. Based on thermal, electronic or microprocessor technology, photocells operate in a number of ways depending of the level of accuracy required.Dusk to dawn sensing – generally inaccurate light detection where the lamp switches ‘ON’ as night falls and switches ‘OFF’ shortly after sunrise.Light level detection – more accurate light detection where the photocell switches at pre-set light levels both at sunset and sunrise, typically 70/35, 55/28, 35/18 or 20/20 lux. Negative switching sets the lamp to ‘OFF’ at a lower level than ‘ON’, with positive switching acting in reverse.

Our products have been used in the telecom and electrical industry since our inception in 1997. These products are still in operation since their installation, which reflects the quality and robustness of these products.We have local facility for metal stamping, shearing, punching, drilling, welding and assembly. Product coating used is hot dip galvanized that comply to BS EN 1461.For Telecommunication we have Eye bolt, clamp pole iron, clamp terminating , clamp pole concrete, clamp pole headring pole iron and pole concrete, thimble open small, stay rod set, stay plate, Hook clamp IB no 1 & no 2, Integral Bearer Clamp no 1 & no 2 and bridle ring

The helically preformed grip is used to hold/pull/tension the galvanized steel stay wire in the installation of the 33/22/11 kV overhead line systems such as pole and tower.

Shackle Insulator

An insulator that is used in distribution networks that works with low voltage is known as a shackle insulator. This insulator is also known as a spool insulator. These insulators can be worked in two positions like horizontal otherwise vertical.

Our Products

Insulated Piercing Connector (IPC)

Insulated Piercing Connector (IPC)

Insulated Piercing Connector (IPC) Holder

Insulated Piercing Connector (IPC) Holder

MODEL : IPCH-01

LV Arrester

MV Arrester

Neutral Link

Overhead Mid Span Joint

Photo Electric Control Unit

Pole Accessories for Telecomunication and Electrical Distribution

Pre-formed Grip

Shackle Insulator

Shackle Insulator